Craftsman 580677130 User Manual 1250 PSI HIGH PRESSURE WASHER Manuals And Guides L0110033

CRAFTSMAN Power Washer Manual L0110033 CRAFTSMAN Power Washer Owner's Manual, CRAFTSMAN Power Washer installation guides

User Manual: Craftsman 580677130 580677130 CRAFTSMAN 1250 PSI HIGH PRESSURE WASHER - Manuals and Guides View the owners manual for your CRAFTSMAN 1250 PSI HIGH PRESSURE WASHER #580677130.

Open the PDF directly: View PDF PDF.
Page Count: 14

_E_/A_/R,._Owner's Manual
CRnFTSMIIN°
1250 PSi 1.5 GPM
DOUBLE INSULATED []
ELECTRIC HIGH PRESSURE WASHER
Model No.
580-677130
CAUTION: Before using this
product, read this manual and
follow all Safety Rules and
Operating Instructions.
SEARS CANADA, Inc., Toronto, Ontario M5B 2B8
PartNo BI245 Drat_ I (2127/97)
SAFETY RULES .......................... 2-3
ASSEMBLY ................................ 4
OPERATION ............................. 5-8
MAINTENANCE ............................ 8
PRODUCT SPECIFICATIONS ................. 8
SERVICE AND ADJUSTMENTS ................ 9
STORAGE .............................. 9
TROUBLESHOOTING ....................... 10
REPAIR PARTS ......................... 11-13
HOW TO ORDER PARTS ............ BACK PAGE
LIMITED ONE YEAR WARRANTY ON CRAFTSMAN ELECTRIC PRESSURE WASHER
For one year from the date of purchase, when this Craftsman High Pressure Washer is maintained and operated
according to the instructions in the owner's manual, Sears will repair, free of charge, any defect in material and
workmanship.
If this washer is used for commercial purposes, this warranty applies for only 90 days from the date of purchase. If
this high pressure washer is used for rental purposes, this warranty applies for only 30 days after date of pur-
chase.
This warranty does not cover:
Repairs necessary because of operator abuse or negligence, including damage resulting from no water being
supplied to pump or failure to maintain the equipment according to the instructions contained in the owner's
manual.
WARRANTY SERVICE IS AVAILABLE BY RETURNING THE HIGH PRESSURE WASHER TO THE NEAREST
SEARS STORE OR OTHER CRAFTSMAN OUTLET CANADA.
This warranty gives you specific legal rights and you may also have other rights, which vary from state to state.
SEARS CANADA, Inc., Toronto, Ontario M5B 2B8
Save these instructions
CAUTION: Before using this product, read I
this manual and follow all Safety Rules and
Operating Instructions.
_, WARNING
RISK OF ELECTROCUTION
Inspect cord before every use. Do not use if cord is
damaged.
Keep all connections dry and off the ground.
Do not touch plug with wet hands.
Double-insulated - When servicing, use only identical
replacement parts.
This product shall only be connected to a power sup-
ply receptacle protected by a Ground Fault Circuit
Interruptor (GFCI).
Read instruction manual before using
_, WARNING
When using this product, basic precautions should always be
followed, including the following:
_, WARNING
To reduce the risk of injury, close supervision is nec-
essary when product is used near children.
Know how to stop the product and bleed the pressure
quickly. Be thoroughly familiar with controls.
Stay alert. Watch what you are doing.
Do not operate the product when fatigued or under the
influence of alcohol or drugs.
Keep operating area clear of all persons.
,_ WARNING
Risk of injury or injection to persons - Do not dis-
charge stream at persons.
High pressure hose can develop leaks from wear,
kinking, abuse, etc. Water spraying from a leak is
capable of injecting material into skin. Do not point the
pressure washer spray at people or animals.
Do not overreach or stand on unstable support. Keep
good footing and balance at all times.
Follow the maintenance instructions specified in the
manual.
This product shall only be connected to a power sup-
ply receptacle protected by a Ground Fault Circuit
Interruptor (GFCI). This is done to comply with
National Electrical Code (NFPA 70) and to provide
additional protection from risk of electrical shock.
TRAINING:
Locate this pressure washer in areas away from
combustible materials, combustible fumes or dust.
Some chemicals or detergents may be harmful if
inhaled or ingested, causing severe nausea, faint_
ing or poisoning. The harmful elements may
cause property damage or severe injury.
Do not allow CHILDREN to operate the Pressure
Washer at any time.
PREPARATION:
Before starting the Pressure Washer in cold
weather, check all parts of the equipment and be
sure ice has not formed there.
Units with broken or missing parts, or without pro-
tective housing or covers should NEVER be oper-
ated.
OPERATION:
_, WARNING
Do not spray flammable liquids,
High pressure stream of water that this equipment
produces can pierce skin and its underlying tis-
sues, leading to serious injury and possible
amputation.
Never aim the gun at people, animals or plants.
For household use. Forindoor or outdoor use.
High pressure spray can cause paint chips or
other particles to become airborne and fly at high
speeds.
Always wear eye protection when you use this
equipment or when you are in vicinity where the
equipment is in use.
Operate the pressure at no more than the PSI
fluid pressure rated for your pressure washer.
Never move the machine by pulling on high pres-
sure hose. Use the handle provided on the top of
the unit.
Use a respirator or mask whenever there is a
chance that vapors may be inhaled. Read all
instructions with the mask so you are certain the
mask will provide the necessary protection
against inhaling harmful vapors.
High pressure spray may damage fragile items
including glass. Do not point spray gun at glass
when in the high pressure mode.
Keep the hose connected to machine and the
spray gun while the system is pressurized.
Disconnecting the hose while the unit is pressur-
ized is dangerous.
Hold the spray gun firmly in your hand before you
start the unit. Failure to do so could result in an
injury from a whipping spray gun. Do not leave
the spray gun unattended while the machine is
running.
Cleaning area should have adequate slopes and
drainage to reduce possibility of a fall due to slip-
pery surfaces.
Keep water spray away from electric wiring or
fatal electric shock may result.
Do not by-pass any safety device on this
machine.
MAINTENANCE AND STORAGE:
Operate and store this unit on a stable surface.
Inspect hose each time before using it. Check all
hoses for cuts, leaks, abrasions or bulging of
cover, or damage or movement of couplings. If
any of these conditions exist, replace hose imme-
diately. Never repair high pressure hose. Replace
it with another hose that meets minimum pressure
rating of your pressure washer.
Store in a clean, dry area. Ideally, the unit should
be stored in a frost-free room.
SERVICING OF A DOUBLE-INSULATED PRODUCT
In a double-insulated product, two systems of insula-
tion are provided instead of grounding. No means of
grounding is provided on a double-insulated product,
nor should a means for grounding be added.
Servicing a double-insulated product requires
extreme care and knowledge of the system and
should be done only by qualified service personnel.
Replacement parts for a double-insulated product
must be identical to the parts they replace, use only
genuine replacement parts. A double-insulated prod-
uct is marked with the words "DOUBLE INSULA-
TION" or "DOUBLE INSULATED".
The symbol [] may also be marked on the product.
EXTENSION CORDS
We do not recommend that you use an extension
cord with this pressure washer. If, however, it is nec-
essary for you to use an extension cord, then you
must use only extension cords that are intended for
outside use. These extension cords are identified by
a marking 'ACCEPTABLE FOR USE WITH OUT-
DOOR APPLIANCES; STORE INDOORS WHILE
NOT IN USE."
,_ LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS. IT I
MEANS "ATTENTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED." I
3
CARTON CONTENTS
The following parts are shipped loose with your pressure
washer:
Main Unit -- pressure washer and electrical cord
Parts Bag (which includes items listed below)
Quick-connect (male and female adaptors)
Product Introduction Video
Nozzle Cleaner Kit
Box marked PARTS INSIDE (which includes items
listed below)
Spray Gun
Wand Extension with Hi-Lo Adjustable Nozzle
High Pressure Hose
Become familiar with each piece before assembling the
pressure washer. Check all contents against the illustra-
tion on Page 5. If any parts are missing or damaged, call
the Pressure Washer Helpline at 1-800-222-3136.
TO REMOVE PRESSURE WASHER FROM
CARTON
Remove parts bag.
Remove box labeld PARTS INSIDE.
Remove main unit with attached electrical cord.
HOW TO SET UP YOUR PRESSURE WASHER
Note: Included with your pressure washer is a video cas-
sette that demonstrates how to set up your pressure wash-
er. If you have a video cassette recorder (VCR), you may
want to view the video before assembling your unit.
Included with this unit is a quick-connect fitting that you
must attach to the water inlet. You can install the male
connector end by hand but you may need to use an
adjustable wrench to tighten it. Check the screen on the
female adaptor. Be sure it is clean and check for holes. If
you see any holes in the screen, do net use that adaptor.
MALE
.FEM_.LE AE
Unwind the high pressure hose and attach it to spray
gun.
Attacn the high pressure hose to the high pressure
outlet and tighten by hand.
HIGH PRESSURE HOSE '_Z__( _r--_.
AttaCh adjustable nozzle extension to spray gun by
inserting threaded end of extension into end of spray
gun and tightening the extension securely by hand.
The extension will click when it is in place properly.
CHECKLIST
Check for proper hose connections (high pressure
and water supply) and for tight connections and that
there are no kinks, cuts, or damage to the high pres-
sure hose.
Provide properwater supply (not to exceed 104°F).
Be sure to read =Safety Rules"and "Operation" sec-
tions before usingthe pressure washer.
4
KNOW YOUR HIGH PRESSURE WASHER
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR HIGH PRESSURE
WASHER. Compare the illustrations with your high pressure washer to familiarize yourselt withthe locations of
various controls and adjustments. Save this manual for 1uture reterence.
MASTER
ONIOFF SWITCH
WATER INLET equipped with
WATER CHECK TM SYSTEM--
electric motor will not start unless
water is supplied to the pump. GENT PICKUP
TUBE AND FILTER
!HIGH PRESSUREOUTLET
PUMP AND MOTOR
QUICK-CONNECT
HOSE
_tF. SPRAY GUN ASSEMBLY
TRIGGER UP TM SYSTEM_
Pressing and releasing the spray
gun trigger starts and stops the
electric motor in the pressure washer.
WAND EXTENSI(
SPRAY GUN ASSEMBLY -Controls the application
of water onto c_eaning surface with triggerdevice,
includes safety latch.
DETERGENT PICKUP TUBE AND FILTER - Mixes
water and detergent in outlet water flow,
HIGH PRESSURE OUTLET- Connection for high
pressure hose.
MASTER ON-OFF SWITCH - This switch ONLY
enables the Trigger UpTM system to function.
QUICK-CONNECT- Easy connection for intake
water supply.
TRIGGER UPTM SYSTEM - Pressing and releasing
the spray gun trigger starts and stops the electric
motor in the pressure washer.
WATER CHECK TM SYSTEM - Electric motor will not
start unless water is supplied to the pump.
5
HOW TO USE YOUR WASHER
If you have any problems operating your pressure wash-
er, please call the pressure washer helpline at
1-800-222-3136.
Note: Includedwith your pressurewasher is a video cas-
sette that demonstrates how to operate your pressure
washer. If you have a video cassette recorder (VCR), you
may want to view the video before assembling your unit.
HOW TO USE ADJUSTABLE NOZZLE
With the adjustable nozzle you can adjust the spray pat-
tern to be either low pressure stream or high pressure
stream. Twisting the nozzle adjusts the spray from a nar-
row spray pattern to a fan spray pattern.
Slide the nozzle attachment forward when you wish to
adjust the spray to low pressure mode. Slide the noz-
zle backward to achieve high pressure.
APPLYING DETERGENT AND CLEANING WITH
ADJUSTABLE NOZZLE
IMPORTANT: Use soaps designed specifically for pres-
sure washers. Household detergents coulddamage the
pump.
To apply detergent follow these steps:
Prepare the detergent solution as required by your
job.
Place the small filter connected to the detergent pick
up tube into the detergent container.
Note: The first step involves applying an appropriate
detergent/solvent solution to penetrate and loosen grime.
ENT PICKUP TUBE
AND FILTER J
"_ The detergent is applied at low pressure to avoid splash-
ing, overspraying and waste. Leave the solution on sur-
face for 3 to 5 minutes to allow solution to work.
NOZZLE IN HIGH PUSH NOZZLE FORWARD
PRESSURE MODE FOR LOW PRESSURE
MODE AND DETERGENT
APPLICATION
Twisting the nozzle adjusts the spray pattern from a
narrow stream to an expanded stream.
Point the nozzle toward the ground and test the spray
pattern.
!
, J
TWIST NOZZLE TWIST NOZZLE FOR
FOR FAN PATTERN NARROW SPRAY
Note: The second step involves cleaning the surface
you have prepared with the pressure washer and then
rinsing it clean.
Slide the adjustable nozzle forward to low pressure
mode. Detergent cannot be applied with nozzle in
high pressure position.
Review the use of adjustable nozzles.
Check that garden hose is connected to water inlet,
check that high pressure hose is connected to spray
gun and pump, turn ON water and start motor (see
TO START THE WASHER).
Apply detergent to a dry surface, starting from the bot-
tom and working up.
Allow the detergent to soak in between 3-5 minutes
before washing and rinsing.
For cleaning, start at lower portionof area to be
washed and work upward, using long, even overlap-
ping strokes.
PATTERN
6
RINSING WITH THE PRESSURE WASHER
AWARNING Be extremely careful if you
must use the pressure washer from ladder,
scaffolding or any other relatively unstable
location. Pressure in a running washer
builds in the wand as you climb. When you
press the trigger, the recoil from the initial
spray could force you to fall, or if you are
too close to the cleaning surface, high
pressure could force you off a climbing
apparatus.
Slide nozzle sleeve rearward to high pressure mode and
wait for detergent to clear. Detergent will not flow when in
the high pressure mode,
When detergent has cleared you may want to use the fan
spray pattern for a more gentle rinsing action. Start at top of
area to be rinsed, working down with same action as for
cleaning.
You can also stop detergent from flowing by simply remov-
ing siphon from bottle.
Note: The high pressure mode is most effective when the tip of
the wand is held between 8 to 24 inches from the surface being
cleaned.
STOPPING YOUR PRESSURE WASHER
The pressurewasher motor is runningonly when the trigger
is engaged.To stop the pressurewasher, releasetrigger
and the motorwill shut OFF.
[_k, WARNING: Never leave th,e pressure wash- [
er unattended while it is plugged into an
electrical outlet and while water is supplied
to the machine.
If using an extension cord,observethe followingspecifications:
CABLE LENGTH WIRE GAUGE
Upto25feet(Sin} 14AWG
50feet(15m) 12AWG
GROUND FAULT PROTECTION
A
A
DANGER Improper connection of the equip-
ment-grounding conductor can result in
eleictrocution. Check with a qualified elec-
trician if you are in doubt as to whether the
outlet is properly grounded. Do not modify
the plug provided with the machine if it will
not fit the outlet. Have a proper outlet
installed by a qualified electrician.
WARNING: To reduce risk of electrocution,
keep all connections dry and off the
ground. DO NOT touch plug with wet
hands.
To comply with the National Electrical Code (NFPA 70),
and to provide additional protection from the risk of elec-
tric shock, this pressure washer should only be connect-
ed to a receptacle that is protected by a ground fault cir-
cuit interrupter (GFCI).
TO TURN ON WASHER
WARNING: To reduce risk of electrocution,
,_ keep all connections dry and off the ground.
DO NOT touch plug with wet hands.
Pressthe Master ON/OFFswitch so it is in the OFF posi-
tion. ,_
\ .
WARNING: Never adjust spray pattern when
water is spraying. Never put hands in front
of spray nozzle to adjust spray pattern.
CAUTION: Gun kicks back. Use both hands.
WARNING: Risk of injury -- Do not dis-
charge stream at persons.
Plug in your high pressure washer.
BEFORE STARTING PRESSURE WASHER
To operate the unit you will needthe following:
Electricalsupply on an isolatedcircuit ratedfor 120volts at
15 ampsshould only be connectedto a receptaclethat is
protectedby a groundfault circuit interrupter(GFCI).
EXTENSION CORDS
Sears recommendsthat you do not use an extensioncord with
this presssurewasher•
If, however, you must use an extensioncord for your applica-
tion, use only an extensioncord that is intendedfor outsideuse.
This extension cord is identifiedby a markng "ACCEPTABLE
FOR'USEWITH OUTDOORAPPLIANCES;STOREINDOORS
WHILE NOT IN USE.
Check that high pressure hose is attached to pump
outlet.
Remove the female quick-connect, attach it to the gar-
den hose of your water supply and then connect water
supply to pump inlet (male quick-connect). Push until
you hear the quick-connect click.
Removewandextension.
PresstheMasterON/OFFswitchtotheONposition.
_L CAUTION:You must be careful at this point.
Anytime you squeeze the trigger, the motor
will start and water will spray out of the gun.
Turn ON water. Water supply should not exceed
104°F. Use a cold water source.
Squeeze trigger on spray gun. Motor will start and
force air from high pressure hose.
Adjust the Safety Latch on spray gun to ON position.
This disables the trigger so you cannot inadvertantly
actuate a spray stream.
Reconnect the wand extension.
Adjust nozzle for correct pressure, spray angle.
Place Safety Latch in OFF position and squeeze trig-
ger on spray gun. Motor will start and water should
stream from the nozzle.
IMPORTANT: The pump will NOT run without the water
supply connected and turned ON.
SIPHONING
We recommend that you DO NOT siphon your water sup-
ply. Connect only to household water supply.
TIPS
Never leave the pressure washer unattended while it
is plugged into an electrical outlet and while water is
supplied to the machine.
Never use the garden hose inlet to siphon detergent
or wax.
If you have the spray nozzle too far away, the clean-
ing will not be as effective.
GENERAL RECOMMENDATIONS
The warranty of the high pressure washer does not cover
items that have been subjected to operator abuse or neg-
ligence. To receive full value from the warranty, operator
must maintain high pressure washer as instructed in this
manual.
BEFORE EACH USE
ADANGER: Water spraying from a leak
is capable of injecting material into skin.
NEVER repair a high pressure hose.
Replace a bad hose with a hose that
meets the minimum pressure rating of
your pressure washer.
Check and Clean Quick-connect Screen: Remove
quick-connect and examine inlet screen on the female
connector. Clean if it is clogged or replace if it is torn.
Check High Pressure Hose: High pressure hose can
develop leaks from wear, kinking, abuse. Inspect hose
each time before using it. Check for cuts, leaks, abrasions
or bulging of cover, or damage or movement of couplings.
It any of these conditions exist, replace hose immediately.
Check Detergent Hose: Examine the filter on the deter-
gent hose and clean if clogged. Hose should fit tightly on
barbed fitting. Examine hose for leaks or tears. Replace
the filter or hose if either is damaged.
Check Gun and Wand: Examine hose connection to gun
and make sure it is secure. Test trigger by pressing it and
making sure it springs back into place when you release
it. Put safety latch in ON position and test trigger. You
should not be able to press trigger.
PRODUCT SPECIFICATIONS
PRESSURE
FLOWRATE
9ETERGENTMIX
WATER SUPPLY
TEMPERATURE
MOTOR
RATED VOLTAGE
CURRENT
1250 osi
!,5 GPM
Useundiluteddeterqent
Not te exceed 104°F
Brush Type
120 volts
13.5 amps
8
NOZZLE MAINTENANCE
If the nozzle becomes restricted or clogged with foreign
materials, such as dirt, excessive pump pressure may
develop. A partially clogged nozzle can cause a pulsing
sensation during use. This generally is not a pump relat-
ed problem, but rather a clogged or partially restricted
nozzle.
If the nozzle becomes clogged or partially restricted,
immediately clean the nozzle with the kit included with
your pressure washer by following these instructions:
Shut off the motor and turn off the water supply.
Separate the wand from the gun.
Adjust the nozzle to the stream position.
Remove nozzle from the end of the wand using a
2ram or 5/64 allen wrench (like the one included in the
kit).
Use the wire included in the kit or a small paper clip to
free the foreign materials clogging or restricting the
nozzle.
Remove additional debris by back flushing water sup-
ply through wand. Back flush between 30 to 60 sec-
onds. Turn wand to stream spray and move nozzle
from low to high pressure while flushing.
Reinstall nozzle into wand. DO NOT overtighten.
Reconnect wand extension to spray gun.
Reconnect the water supply, turn ON the water, and
start the motor.
Test the pressure washer by operating with nozzle in
the high and the low pressure positions.
Water should not remain in the unit for long periods of
time. Sediments of minerals can deposit on pump parts
and "freeze" pump action. A_ler each time you are fin-
ished using your pressure washer, follow this procedure:
Flush detergent hose by placing the injector filter into
apail of ctear water while running Pressure Washer
with nozzle in low pressure mode. Flush until you can
see clear water flowing through hose.
Switch the Master ON/OFF switch to OFF, unplug it,
then remove all the hoses.
Store the pressure washer and its components in such
a way as to protect it from freezing.
Store in a clean, dry area. Ideally, the unit should be
stored in a frost-free room.
Coil the high pressure hose and inspect it for damage.
Cuts in the hose or fraying of it could result in leaks
and loss of pressure. Should any damage be found,
reptacethe hose. DO NOT attempt to repair a dam-
aged hose. Replace the hose with the genuine
Craftsman part.
Brain water from hose and properly store it to prevent
cuts and general wear.
PROBLEM
PressureWasherwillnotstart,
CAUSE
1. No electrical poweris available.
2. Motor overheats.
Pressure Washer does not
come up to pressure.
High pressurespray is irregular.
No intake of cleaning agent.
3. Trigger not open.
4. Electrical defect.
1. Spray gun is in low pressure mode.
2. Pump is sucking air,
3. Water filter clogged,
4. Pump not bled to remove air.
5. Pump is defective.
1. Nozzle or watersupplyis restricted.
2. Water supply inadequate.
1. Wrong nozzle setting.
2. Nozzle clogged.
3. Suction filter clogged.
CORREC_ON
1. Check cable, plug, power socket
and fuse/circuit breaker.
2. Length of exle_ion cord is well
beyond 50 feet.
3. Open trigger.
4. Contact Sears Service Department.
1.
2.
3,
4.
Adjust nozzle to high pressure
mode.
Water hose must be 1/2" diameter
Make sure water supply is ON.
Make sure water supply is clean.
Check all connections for leaks or
blockage.
Clean filter.
Switch OFF washer, press trigger,
switch ON washer while pressing
trigger. Repeat if necessary.
5. Contact Sears Service Department,
1. Position nozzle completely in low
pressure orhigh pressure position.
Unplug unit and clean nozzle.
2. Turn ON water to full position.
Operate washer in suction
operation withopen container.
1. Adiust nozzle to low pressure mode.
2. Clean nozzle.
3. Clean filter in suction nozzle.
CRAFTSMAN 1250 PSI HIGH PRESSURE WASHER 580-677130
2O ?
15
/l
CRAFTSMAN 1250 PSI HIGH PRESSURE WASHER 580-677130
81 56
65
10 90
92
90
ITEM PART NO. DESCRIPTION
1 21144
3 21054
4 21055
5 20138
6 20928
7 20218
8 21342
9 21525
10 96462
ASSy, Motor Complete (1 req.)
Boot, Rubber (1 req.)
Grommet, Rubber (1 req.)
Switch, Auto {,1 req.)
Housing, Auto-switch (1 req.)
Cap, Retainer (1 req.)
Ass'y, Piston (1 req.)
Wiper, Piston Bore (1 req.)
Decat, Circuit (1 req.)
ITEM PART NO. DESCRIPTION
11 Al!28
12 21318
13 2O212
14 Al132
15 Al131
16 A1495
Decal, Unit (1 req.)
Decal, Instructions (1 req.)
Spring 15.08 x dia. 1.62CS
x 22.3mm (1 req.)
Seat, Ball (1 req.)
Plug, Expansion {1 req.)
Taptite M4 - 0.7 x 10mm,
Switch Mounting 12 req.)
12
CRAFTSMAN 1250 PSI HIGH PRESSURE WASHER 58__-677130
ITEM PART NO. DESCRIPTION
17 B1077
18 81060
19 21124
20 21123
21 21126
22 21125
23 20217
24 Al130
25 95380
26 97852
27 A1575
28 A1040A
29 28739A
30 48031G
31 97840
32 97841
33 97837
34 97835
35 B1026
36 96307
37 97838
38 A1111A
39 97839
40 97851
41 97832
42 40946
43 93873
44 93667
45 97831
46 93680
47 20140
48 99503
49 97830
50 97962
51 97824A
52 97826
53 97825
54 97716
55 97829
56 97822
57 20610
ITEM PART NO. DESCRIPTION
"O" Ring, Venturi (1 req.) 58 97823
Venturi, Chem. Injector(1 req.)
Ring, Backup dia, 4.34 Id x 59 97834
1.24 (1 req.}
"O" Ring dia. 3.68 Id x 1.78 60 97833
CS [.070"] (1 req.) 61 B1125
Ring, Backup dia. 26.0 ID (1 req.)
"O" Ring dia. 25.07 ID x 2.62 62 98806
CS [.103"] (1 req.) 63 97893
Stop Piston Return (1 req.) 64 20984
Spring, Pop-off Va ve (1 req.) 65 98801
Spring, Chem. Injector (1 req.) 66 97892
Ball, dia. 3/16" Pop-off Valve 67 20985
(1 req.)
Barb, Hose, Brass with nylon 68 20986
Insert (1 req.) 69 84543B
Hose, Chem (1 req.) 70 98805
Tie Wrap (1 req.) 71 84358
Hose Clamp, 3/16" (1 req.) 72 97934
"O" Ring, Hi-press Port dia.
15.6 x 1.78ram (3 req.) 73 99349
Cap, Check Valve (3 req.) 74 B1053
"O" Ring, HFpress Trans dia. 75 B1052
9.2 x 2.62mm (1 req.) 80 97694
"O" Ring, Hsg Seal, dia. 82.2 x 81 97695
2.62mm (2 req.) 82 21781
Vinyl Cap (1 req.) 83 21782
Decal, 800 # (1 req.) 84 76353A
Assy., Check Valve, Inlet (3 req.) 85 A1484
Head Pump (1 req.) 86 A1485
Assy., Check Vak,e, Outlet (3 req.) 87 97855
"O" Ring, Piston dia. 10.82 x
1.78ram (3 req.) 88 A1041
Piston. dia. 15 x 65mm (3 req.) 89 95379
Bolt, SHCS M6- 1.0 x 35mm 90 99350
(4 req.) 91 97809
Lockwasher, M6 Ribbed (7 req.) 92 95602F
Seal, Piston "U" Cup (3 req.) 93 21779
Spacer, Pilot (3 req.) 94 B1236D
Seal, Oil-piston dia. 15 TC4
(3 req.)
Housing, Piston (1 req.)
Spring, Piston Return (3 req.)
Retainer, Piston Spring (3 req.)
Bolt, SHCS M6-1.0 x 25ram 71 75199
(3 req.) 71 75189
Bearing, Needle dia. 40 x 71 75190
60mm {1 req.) 71 75184
Washer, Brg dia. 40 x 60 x 71 75187
lmm (1 req.) 71 75100
Washer, Brg dia. 36 x 60 x 71 75101
6mm (1 req.) 71 75102
Cam, Axial4.3 Mm Stroke {1 req.) 71 75103
Gear, Axial Cam (1 req.) 71 75104
Brg Needle Thrust dia. 35 x 71 75183
52mm (1 req.) 71 76477
Washer, Brg dia. 35 x 55 x
3ram (1 req.)
Washer, Brg dia. 35 x 52 x
1ram (1 req.)
Bearing, Needle dia. 8 x 12 x
10mm (2 req.)
Shaft, Idler Axial Cam (1 req.)
Nut, M5-0.8 LH Thread
{1 req.)
Foam, Air In, Fan-end (1 req.)
Housing, Switch and Cord (1 req.)
Switch, Rocker 16A (1 req.)
Mount, Rubber (4 req.)
Cover, Motor (1 req.)
Enclosure, Rocker Switch,
Boot (1 req.)
Boot, Rocker Switch (1 req.)
Plastite3.5mm x 12mm (2 req.)
Cord, Power (1 req.)
Plastite #6-19 x .75mm (5 req.)
"O" Ring, Chk Valve alia. 12.4
x 1.78mm (3 req.)
Relief, Strain Cord (1 req.)
ETL Decal (1 req.)
Data Decal (1 req.)
Housing, Inlet (1 req.)
Housing, Outlet (1 req.)
Quick Disconnect, Male (1 req.)
Quick Disconnect, Female (1 req.)
Plug Taper dia. 5.4 (1 req.)
Lock Nut, Strain Rel ef (1 req.)
Seal Ring, Strain Relief (1 req.)
"O" Ring dia. 6.5 x 2.01 mm
(1 req.)
Filter, Chem Hose (1 req.)
Ball, Chemical Injector (1 req.)
Screw #6 Plastite (5 req.)
Spray Gun (1 req.)
Wand Extension (1 req.)
High Pressure Hose (1 req.)
Nozzle, 1.15mm (1 req.)
PARTS NOT ILLUSTRATED
B1245 Owner's Manual (1 req.)
OPTIONAL ACCESSORIES (not shown)
Rotating Brush Kit
Utility Brush Kit
Broom Brush Kit
Electric Turbo Nozzle
Garden Hose Quick-connect Kit
Multipurpose Cleaner
Deck Wash
Vehicle Wash
Degreaser
Spray Wax
Multipurpose Storage Bracket
Electric Cart
13
Dear Customer,
In manufacturing this product, many steps have been taken to provide you with the highest quality. Unfortunately, errors
or emissions occasionally occur. In the event that you find a missing or detective part, please contact your nearest Sears
store.
SERVICE AND REPAIR PARTS
CALL 1-800-665-4455 *
Keep this number handy should you require a
service call or need to order repair parts.
If ordering parts make sure you have the name, make
and model no. of the merchandise and the name and number
of the part you wish to order.
*If calling locally, please use one of the following numbers:
Regina - 566-5124 Montreal - 333-5740
Toronto - 744-4900 Halifax - 454-2444
Kitchener - 894-7590 Ottawa - 738-4440
Vancouver - 420-8211
If you have any suggestions that would help us to improve our assembly/operation instructions of this product, please
write them down and mail to:
Sears Canada, Inc.
222 Jarvis Street
Toronto, Ontario
M5B 2B8
Attention: Buyer Dept. 671
NAME:
ADDRESS:
POSTAL CODE:
COMMENTS:
Model No.
PHONE #:

Navigation menu