Craftsman 320 17562 Users Manual

32017562 b0bfa028-52e1-4c00-992f-8c7f63ba4dbe Craftsman Cordless Drill 320.17562 User Guide |

2015-01-05

: Craftsman Craftsman-320-17562-Users-Manual-160323 craftsman-320-17562-users-manual-160323 craftsman pdf

Open the PDF directly: View PDF PDF.
Page Count: 15

DownloadCraftsman Craftsman-320-17562-Users-Manual-  Craftsman-320-17562-users-manual
Open PDF In BrowserView PDF
Operator's

Manual

ICRA

MAN°I

flEX E
12.0-VOLT LITHIUM-ION
CORDLESS RIGHT-ANGLE
IMPACT DRIVER
Model No. 320.17562

c_ius
LISTED
• Warranty
Powered by an
ENERGYSTAR_
qualified battery
charger for a
better environment

_k WARNING:

To reduce

• Safety
• Assembly
• Operation
• Maintenance

the risk of

injury, the user must read and understand
the Operator's manual before using
this product.

Sears Brands Management
IL 60179 U.S.A.
www.craftsma n.com

• Espa_ol
Charge battery
before first use

Corporation, Hoffman Estates,

InuPL4
-'1ml_ [o_ [_o__

Warranty

page 2

Safety Symbols

page 3

Safety Instructions

page 5

Description

page 9

Assembly

page 10

Operation

page 11

Maintenance

page 19

Troubleshooting

page 21

Exploded

page 22-24

View and Part List

Sears Repair Parts Phone Number

The purpose of safety symbols is to attract your attention to possible dangers.
The safety symbols and the explanations with them deserve your careful
attention and understanding.
The symbol warnings do not, by themselves,
eliminate any danger. The instructions and warnings they give are no substitutes
for proper accident prevention measures.
WARNING:
Be sure to read and understand all safety instructions in this
manual, including all safety alert symbols such as "DANGER," "WARNING,"
and "CAUTION"
before using this Right-Angle Impact Driver. Failure to following
all instructions listed in this manual may result in electric shock, fire, and/or
serious personal injury.
SAFETY

SYMBOL

MEANING

SAFETY ALERT SYMBOL:

Back Cover

May be used in conjunction

CRAFTSMAN ONE YEAR LIMITED WARRANTY
FOR ONE YEAR from the date of purchase, this power tool, battery
pack and charger are warranted against any defects in material or
workmanship. With proof of purchase, defective product will be
replaced free of charge.
For warranty coverage details to obtain free replacement,
web site: www.craftsman.com

or pictographs.
which,

if not

_,

situation,

which,

if not

situation,

which,

if not

WARNING:

Indicates

a potentially

hazardous

could result in death or serious injury.

CAUTION:

avoided,

Indicates

an imminently

may result in death or serious

hazardous
injury.

NOTE: These inform the user of import information and/or instructions that
could lead to equipment or other property damage if they are not followed. Each
message is preceded by the word "NOTE," as in the example below:
NOTE: Equipment
not followed.
WARNING:

Hoffman Estates, IL 60179

by a qualified

and/or

property

damage

may result if these instructions

To ensure safety and reliability,
service technician

are

all repairs should be performed

at a Sears parts & Repair Service Center.

INSTRUCTIONS!

_i, WARNING: The operation of any power tool can result

READ ALL INSTRUCTIONS

in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool
operation, always wear safety goggles or safety glasses
with side shields and a full-face shield when needed.

This cordless 12V Right-Angle Impact Driver has many features for making its
use more pleasant and enjoyable. Safety, performance, and dependability
have
been given top priority in the design of this product making it easy to maintain
and operate.

We recommend a Wide Vision Safety Mask for use over
eyeglasses or standard safety glasses with side shields.
Always use eye protection which is marked to comply with
ANSI Z87.1

_lk WARNING;
Some dust created by using power tools contains chemicals
known to the state of California to cause cancer and birth defects or other

17562

OR CAUTION.

situation,

_,

This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.

reproductive

with other symbols

WARNING,

visit the

This warranty is void if this product is ever used while providing
commercial services or if rented to another person.

SAVE THESE

DANGER,

DANGER: Indicates an imminently hazardous
avoided, will result in death or serious injury.

avoided,

This warranty does not cover nut driver bits and screw driver bit which
are expendable parts that can wear out from normal use within the
warranty period.

Sears Brands Management Corporation,

Indicates

harm.

Manual_Revised_$O

0607

Page 2

17562

ManuaLRevised_iO

0607

Page 3

SAVE THESE INSTRUCTIONS
Some of these following
and learn their meaning.

symbols may be used on this tool. Please study them
Proper interpretation
of these symbols will allow you to

operate the tool better and safer.
SYMBOL

GENERAL
_,

NAME
Volts

Voltage

A

Amperes

Current

Hz

Hertz

Frequency

W

Watt

Power

min

Minutes

WARNING:

Read all safety warnings

the warnings and instructions
personal injury.

DESIGNATION/EXPLANATION

V

POWER TOOL SAFETY WARNINGS

Save all warnings
(cycles

and instructions.

may result in electric

and instructions

for future

Failure to follow

shock, fire and/or

reference.

The term "power tool" in all warnings refers to your mains-operated
power tool or battery-operated
(cordless) power tool.

per second)

serious

(corded)

WORK AREA SAFETY
Time

•
Alternating
--_
nO
]

Direct

Current
Current

Type or a characteristic

No Load Speed
Class

.../min

Type of current

Rotationai

II Construction
Per Minute

speed,

Double-insulated

of current

Keep your work area clean and well lit. Cluttered
accidents

or dark areas invite

Do not operate power tools in explosive environments, such as in the
presence of flammable liquids, gases, or dust. Power tools create sparks,
which may ignite the dust or fumes.

at no Ioad
construction

Revolutions,
strokes, surface
orbits, etc., per minute

Keep children and bystanders away while operating a power tool.
Distractions may cause you to lose control.

speed,

ELECTRICAL SAFETY
Wet Conditions

Read The Operator's

Alert

Manuai

Eye Protection

O

Safety

,_

No Hands

No Hands

No Hands

No Hands

Alert

Symboi

Symbol

Symboi

Symboi

Hot Surface

17562 ManuaLRevised_$O 0607

locations.
Do not expose

Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce the risk of electric shock.

to rain or use in damp

read and understand
operator's
manuai
To reduce the risk of injury, user must
before using this product.

Avoid body contact with grounded surfaces, such as pipes, radiators,
ranges, and refrigerators.
There is an increased risk of electric shock if your
body is grounded.

glasses with side shields and a full face
Always wear safety goggles or safety
shield when operating this product.
Precautions

that involve

Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.

your safety.

Do not abuse the cord. Never use the cord for carrying, pulling, or
unplugging the power tool. Keep the cord away from heat, oil, sharp
edges, or moving parts. Damaged or entangled cords increase the risk of
electric shock.

Failure will
blade
to result
keep your
in serious
hands personal
away frominjury.
the

Failure will
blade
to result
keep your
in serious
hands personal
away frominjury.
the

•

When operating a power tool outdoors, use an extension cord suitable
for outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.

•

If operating a power tool in a damp location is unavoidable, use a
residual current device (RCD) protected supply. Use of an RCD reduces
the risk of electric shock.

•

NOTE: The term "residual current device (RCD)" may be replaced by the
term "ground fault circuit interrupter (GFCI)" or "earth leakage circuit breaker
(ELCB)".

Failure will
blade
to result
keep your
in serious
hands personal
away frominjury.
the

blade
in serious
Failure will
to result
keep your
hands personal
away frominjury.
the

To reduce
avoid
contact
the with
risk of
anyinjury
hot surface.
or damage,

Page 4

17562

ManuaLRevised_lO

0607

Page 5

•

Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained users.

Use the battery only with the charger listed:
BATTERY

PACK

CHARGER

320.11221
PERSONAL

320.10006

Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the
power tool's operation. If damaged, have the power tool repaired before
use. Many accidents are caused by poorly maintained power tools.

SAFETY

Stay alert, watch what you are doing, and use common sense when
operating a power the tool. Do not use a power tool while tired or under
the influence of drugs, alcohol, or medication. A moment of inattention
while operating power tools may result in serious personal injury.

Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.

Use the power tool, accessories, blades, etc. in accordance with these
instructions and in the manner intended for the particular type of
power tool, taking into account the working conditions and the work
to be performed. Use of the power tool for operations different from those
intended could result in a hazardous situation.

Use personal protective equipment. Always wear eye protection.
Protective equipment, such as dust mask, non-skid safety shoes, hard hat,
or hearing protection, used for appropriate conditions will reduce personal
injuries.
Prevent unintentional starting. Ensure that the switch is in the OFF
position before connecting to power source and/or battery pack,
picking up, or carrying the tool. Carrying power tools with your finger
on the switch or energizing power tools that have the switch on invites
accidents.

BATTERY

TOOL USE AND CARE

Recharge only with the charger specified by the manufacturer.
A charger
that is suitable for one type of battery pack may create a risk of fire when
used with another battery pack.

Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result
in personal injury.

Use power tools only with specifically designated battery
any other battery packs may create a risk of injury and fire.

Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.

When the battery pack is not in use, keep it away from other metal
objects, such as paper clips, coins, keys, nails screws, or other small
metal objects that can make a connection from one terminal to another.
Shorting the battery terminals together may cause burns or a fire.

Dress properly. Do not wear loose clothing or jewelry. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewelry or
long hair can be caught in moving parts.
If devices are provided for the connection of dust extraction and
collection facilities, ensure that these are connected and properly used.
Use of these devices can reduce dust-related
hazards.
POWER TOOL USE AND CARE

Use of

Under abusive conditions, liquid may be ejected from the battery;
avoid contact. If contact accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help, Liquid ejected from the
battery may cause irritation or burns.
SERVICE
•

Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and more safely at
the rate for which it was designated.
Do not use the power
power tool that cannot
be repaired.

packs.

Have your power tool serviced by a qualified repair person using only
identical replacement
parts. This will ensure that the safety of the power
tool is maintained.

When servicing a power tool, use only identical replacement

tool if the switch does not turn it on and off. Any
be controlled with the switch is dangerous and must

parts.

Follow instructions in the Maintenance section of this manual. Use of
unauthorized parts or failure to follow Maintenance instructions may create a
risk of shock or injury.

Disconnect the plug from the power source and/or the battery pack
from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
17562

ManuaLRevised_iO

0607

Page 6

17562

ManuaLRevised_iO

0607

Page 7

SPECIFIC SAFETY RULES FOR CORDLESS RIGHT ANGLE IMPACT DRIVER
Hold power tools by insulated gripping surfaces when performing an
operation where the tool may contact hidden wiring or its own cord.
Contact with a "live" wire will also make exposed metal parts of the tool
"live" and shock the operator.
Secure the workpiece. Clamping
in place better than the hand

devices or a vise will hold the workpiece

Always wait until the machine has come to a complete stop before
placing it down. The tool can jam and lead to loss of control over the power
tool.

Before performing any kind of work on the machine (e. g., maintenance,
tool change, etc) as well as when transporting and storing it, always
set the rotational direction switch to the center position. Unintentional
activation of the On/Off switch may result in personal injury.
Do not open the battery.
Protect

KNOW YOUR RIGHT-ANGLE IMPACT DRIVER (Fig.l)
Fig. 1

Sleeve
Direction of
Rotation Selector
(Forward/Center
Lock/Reverse)

LED
Worklight

FuelGauge

There is risk of a short circuit.

the battery from heat and fire. There is risk of explosion.

Wear ear protectors
hearing loss

_]__o_j

with impact

drills. Exposure

Variable

Battery Release
Button

Speed Trigger
Switch

to noise can cause

Use protective gloves when removing the bit from the tool, or first allow
the clamp to cool down. The bit may be hot after prolonged use.
Use protective gloves when operating
to keep you from being burnt and hurt.

the tool. Protective

gloves can help

Battery Pack
PRODUCT

Keep your hands away from the motor-housing
from the vents during operation.

vents. Hot gas comes

Do not operate the tool at full-load for more than 30 seconds, as this can
cause the motor to become too hot, which may damage the motor.

Release the trigger immediately when the fasteners are sufficiently
tightened to avoid breaking the fasteners.
For best results, your battery tool should be charged in a location where the
temperature is more than 32°F (O°C) but less that 104°F (40°C). Do not store
outside or in vehicles.

Motor

12 Volt DC

Collar

1/4"

Switch

VSR (Variable Speed Reversible)

No Load Speed

0-2100

RPM

Impacts

0-3400

BPM

Manual_Revised_SO

0607

Page 8

per minute

Torque

700 in.lbs

Driver Weight

(without battery)

1.83 Ibs (without battery)

Battery Type

Lithium-Ion

Battery Voltage

12 Volt DC

Charger

120-Volts,

Optimum

17562

SPECIFICATION

17562

Input
Charging

ManuaLRevised_lO

Temperature

0607

60 Hz AC only

32°F (0°C) -104°F (40°C)

Page 9

A
ABt,WARNING: The safe use of this product requires an understanding
of the
information on the tool and in this operator's manual, as well as knowledge of
the project you are attempting. Before use of this product, familiarize yourself
with all operating features and safety rules.

VARIABLE SPEED
The variable-speed
trigger switch delivers higher speed with increased
and lower speed with decreased trigger pressure.
FORWARD/CENTER

PACKING

LED WORK LIGHT
This feature

Right-Angle Impact Driver, soft case, 1-3/8" Phillips screwdriver
bit, 1A" nut
driver bit, 3/8" nut driver bit, 5/16" nut driver bit, operator's manual.

provides

level.

WARNING:

If any part is broken or missing,

Important

WARNING:

Do not attempt

WARNING:

To prevent

do not attempt

Impact Driver or

Impact

personal

2.

While charging

a battery,

3.

If the batteries

do not charge properly:

completely

assembled.

•

Carefully remove the tool and any accessories
all items listed in the packing list are included.

•

Inspect the tool carefully
during shipping.

•

Do not discard the packing material
satisfactorily operated the tool.

17562

Manual_Revised_SO

0607

from the box. Make sure that

to make sure that no breakage

or damage

until you have carefully

if batteries

the charger will normally become

are charged

warm.

in a lamp or other appliance

B. Determine whether the outlet is connected to a light switch that turns the
power off when you turn out the lights; if so, make sure that the power is
turned on.
4.

The battery pack should be recharged when it fails to produce sufficient
power on jobs that were previously done easily or when the FuelGauge
shines red to indicate that the charge is depleted. Do not continue to use
the tool under these conditions. Repeat the charging procedure.

5,

Unplug the charger from the power supply before disconnecting
tool. Unplug the charger before attempting to clean.

6.

Battery life depends

7.

The charger is intended

Driver when

UNPACKING
has been shipped

can be obtained

to plug in the

starting that could cause serious

injury, always remove the battery pack from the Right-Angle
assembling parts.

This product

notes

A. Verify the current at the outlet by plugging
and turning it on.

to modify this 12V Right-Angle

accidental

charging

Longest life and best performance
at normal room temperature.

create accessories not recommended
for use with this tool. Any such alteration
or modification
is misuse and could result in a hazardous condition leading to
possible serious injury.
A

pack is not fully charged!

1.

power cord, attach the battery pack or operate the 12V Right-Angle Impact
Driver until the broken or missing part is replaced. Failure to do so could result
in possibly serious injury.
a

INDICATOR

First, read the safety rules, and then follow the instructions in the sections
entitled "Important
charging notes" and "Charging
the battery".

r_,."_"]
•
d _ I:] a5"4
A

CAPACITY

NOTE: The new battery

FuelGauge
charge

listed on

LIST

LOW-BATTERY

the LED worklight.

please refer to the numbers

[,] d d-'T-,_d[,] _1

The direction-of-rotation
selector located above the trigger switch changes
the direction of bit rotation. Setting the trigger switch in the OFF (center lock)
position helps to reduce the possibility of accidental starting.

Indicates the battery-pack

If any parts are damaged or missing,
the back page of operator's manual.

pressure

LOCK/REVERSE

Pressing the trigger switch illuminates
extra light for increased visibility.

•

occurred

inspected

and

Page 10

Unlike other battery
entire run time. The
you work. To signal
charged, the power

on usage, storage temperature

it from the

and time.

to be used in a vertical or floor-mounted

position.

types, Lithium-Ion battery delivers fade-free power for their
tool will not experience a slow, gradual loss of power as
that the battery is at the end of its run time and needs to be
to the tool will drop quickly.

NOTE: The LED worklight may flash slowly and the FuelGauge may not
illuminate in the case of an overload or high temperature (see BA-I-i-ERY
PROTECTION, Page 12).

17562

ManuaLRevised_lO

0607

Page 11

BATTERY

PROTECTION

Charge the Lithium-Ion
battery pack with the
correct charger.

1.

The battery circuitry protects the battery pack from extreme temperature,
over-discharge,
and over-charge.
To protect the battery from damage and
prolong its life, the battery pack circuitry will turn off the battery pack if it
becomes overloaded or if the temperature becomes too high during use. This
may happen in extremely high torque, binding, and stalling situations. This
intelligent system will shut down your battery pack if its operating temperature
exceeds 176°F (80°C) and will begin normal operation when it returns to 32°F
(0°C) - 104°F (40°C).
The LED worklight will begin to flash slowly if the battery circuitry
momentary overload.

detects

2.

Connect the charger to a
power supply.

3.

Align the raised ribs of the
battery pack with the slot in
the charger.

4,

Insert the battery pack into
the charger (Fig. 2).

5,

The charger will
communicate
with the

a

NOTE: A significantly reduced run time after fully charging the battery pack
indicates that the battery is near the end of its usable life and must be replaced.
COLD WEATHER

battery pack to evaluate the
condition of the battery pack.

OPERATION

This Lithium-Ion battery pack will provide optimal performance
in temperatures
between 32°F (0°C) and 104°F (40°C). When the battery pack is very cold, it may
"pulse" for the first minute of use to warm itself. Install the battery pack in the
tool and use the tool in a light application; after about a minute, the battery pack
will have warmed itself and will operate normally.
WHEN TO CHARGE

THE BATTERY

6.

The green lights will flash while the battery pack is charging. After charging
is complete, the green LED on the charger will be on. The flickering red light
indicates a defective battery or a bad connection between the battery and
the charger.

7.

The battery pack will fully charge if left on the charger,
overcharge.

PACK

It is not necessary to run down the battery pack charge before recharging. The
Lithium-Ion battery can be charged at any time and will not develop a "memory"
when charged after only a partial discharge.

Due to Lithium-Ion fade-free properties, the only time it is necessary to charge
the Lithium-Ion battery pack is when the pack has reached the end of its charge.
The orange LED on the FuelGauge indicates
approximately
one half of its charge.
The red LED on the FuelGauge
to be charged.

indicates

pack is depleted

THE BATTERY

0607

RED
LED

_)

GREEN
LED

ACTION

when battery returns to
32OF (0oc)_104OF (40oc)

Defective

Flashing

Off

Battery pack or
Charger/Adapter
is
defective

CHARGING

Charging

Off

Flashing

Fully
charged

Off

On

FULL
BATTERY

BATTERY
DEFECTIVE

and needs

_

Hot/Cold
battery

On

will begin

Off

HI/LO
TEMP.
(SEE
MANUAL)

BATTERY

partially charged.

A fully discharged battery pack will charge in about 30 minutes
temperature between 32°F (0°C) and 104°F (40°C).

ManuaLRevised_i0

BA-i-rERY
PACK

and

Charging

PACK (Fig. 2)

NOTE: This Lithium-Ion battery pack is shipped
the first time, fully charge the battery pack.

:$7562

(Fig. 3)

Charging

Charge the battery pack as needed.
HOW TO CHARGE

OF CHARGER

LED INDICATOR

that the battery has used

the battery

but it will not

NOTE: For your convenience, the charger can operate with most generators
inverters rated at 300 watts or higher.
LED FUNCTIONS

Remove the battery pack from the tool when it is convenient for you and your
job. "Top off" the battery pack charge by charging it for a time before starting a
big job or long period of use.

I Fig. 2

Before using it

0

Charging

is complete

in a surrounding

Page :$2

:$7562

ManuaLRevised_:$0

0607

Page :$3

CHARGING

A HOT BATTERY

PACK

If the battery pack is above normal temperature range, the red LED will
illuminate and the green LED will be off. When the battery pack cools down to
approximately
104°F (40°C), the charger will automatically
begin charging.
CHARGING

A COLD BATTERY

PACK

3.

If a different battery pack charges
pack (see Maintenance section).
If a different
defective.

BATTERY

normally,

battery pack also indicates

dispose

"defective,"

of the defective

IocW reverse) selector

in the center

When placing the battery

pack in the tool, be sure that the

raised rib on battery pack aligns with the groove inside the Right-Angle Impact
Driver and that the latches snap into place properly. Improper attachment of the
battery pack can cause damage to internal components.

If the charger detects a problem with the battery, the battery may be defective:
the red LED will begin flashing and the green LED will be off.

2.

(forward/center

Align the raised rib on the battery pack with the grooves in the Right-Angle
Impact Driver, and then insert the battery pack into the tool.

_L. CAUTION:

DEFECTIVE BATTERY

If registering as defective, remove and reinsert the battery pack in the
charger. If the LED status reads "defective" a second time, try charging
different battery pack.

2.

of rotation

NOTE: Make sure that the latch on the battery pack snaps into place and that
the battery pack is secured to the tool before beginning operation.

If the battery pack is below the normal temperature range, the red LED
will illuminate and the green LED will be off. When the battery warms to a
temperature of more than 32°F (0°C), the charger will automatically
begin
charging.

1.

direction
position.

TO DETACH BATTERY PACK (Fig, 4)
1. Lock the trigger switch on the Right-Angle
direction of rotation
Lock position.

a
2.

Depress the battery release buttons
pack to release the battery pack.

3.

Pull the battery pack out and remove it from the tool.

battery

the charger may be

Impact Driver by placing the
(forward / center lock/reverse)
selector in the Center

_lk WARNING:

If the battery pack is being charged within a normal surrounding temperature
range (32°F to 104°F), the green LED will begin flashing and the red LED will be
off. The battery pack will reach a full charge in 30 minutes.

BATTERY FULL
If the battery pack is within normal temperature range, the green LED will
illuminate and the red LED will be off. The battery pack is fully charged and
ready to use. The battery pack will fully charge, but will not overcharge, if left on
the charger.
Fig. 4
NOTE: The charger may
become warm with several
continuous charge cycles. This
is part of the normal operation
of the charge. Charge in a well
ventilated area.

TRIGGER

SWITCH

(Fig, 5)

To turn it OFF, release the
trigger switch.
SPEED (Fig,5)

The variable-speed
trigger
switch delivers higher speed
with increased trigger pressure
and lower speed with decreased
trigger pressure.

condition.

Therefore,

the

always be locked when the tool is not in use

Fig. 5

To turn the 12V Right-Angle
Impact Driver ON, depress the
trigger switch.

VARIABLE

on the both sides of the battery

Battery tools are always in operating

direction-of-rotation
selector should
or when carrying it your side.

CHARGING

located

Variable-speed
trigger switch

Directionof-rotation
selector
(Forward/
Center
Lock/
Reverse

TO ATTACH BATTERY PACK
(Fig. 4)
1.

17562

Lock the trigger switch on
the Right-Angle Impact
Driver by placing the
ManuaLRevised_$0

0607

Page 14

17562

ManuaLRevised_10

0607

Page 15

DIRECTION-OF-ROTATION
REVERSE) (Fig. 5)

SELECTOR

(FORWARD/CENTER

LOCK/

LED WORKLIGHT

(Fig. 7)

Fig. 7

Position the direction-of-rotation
rotation.

selector to the left of the tool for forward

The LED worklight, located on
the front of the 12V Right-Angle
Impact Driver, will illuminate
when the trigger switch is
depressed.

2.

Position the direction-of-rotation
rotation.

selector to the right of the tool for reverse

This provides additional light on
the surface of the workpiece for
operation in lower-light areas.

3.

Setting the switch in the OFF (center lock) position
possibility of accidental starting when not in use.

_i,

CAUTION:

The direction of bit rotation is reversible and is controlled by a selector located
above the trigger switch. With the Right-Angle Impact Driver held in normal
operating position:
1.

To prevent gear damage,

Impact Driver to come to a complete
rotation.

The LED worklight will turn
off when the trigger switch is
released.

helps reduce the

always allow the 12V Right-Angle

stop before changing

the direction

INSTALLING

of
1.

NOTE: The 12V Right-Angle Impact Driver will not run unless the direction
rotation selector is engaged fully to the left or right.
ELECTRIC

of

BRAKE

2.

The green LED on the
FuelGauge indicates that the
battery is fully charged.
The orange LED on the
FuelGauge indicates that the
battery has used approximately
one half of its charge

ManuaLRevised_$O

0607

Fig. 8

With one hand, pull the
sleeve toward the front of

3.

With the other hand, insert
a 1/4-in. shank bit into the
hexagonal
retainer.

Fig. 6

4.

_i,
FuelGauge

hole in the bit

Release the sleeve and
check that it returns to its
original

tP

position.

WARNING:

correctly

If the sleeve does not return to its original

installed.

WARNING:

Retry until the bit is properly

Use protective

position,

the bit is not

installed.

gloves when removing

the bit from the tool, or

first allow the bit to cool down. The bit may be hot after prolonged

use.

J.z/

C

REMOVING

The red LED on the FuelGauge
indicates the battery pack
is depleted and needs to be
charged.

17562

Lock the trigger switch by
placing the direction-ofrotation selector in the OFF

the tool, and hold it in place.

(Fig. 6)

This tool is equipped with a
FuelGauge that indicates the
battery pack charge level.

BITS (Fig. 8)

(center) position.

To stop the 12V Right-Angle Impact Driver, release the trigger switch and
allow the tool to come to a complete stop. The electric brake quickly stops the
rotation. This feature engages automatically
when you release the trigger switch.
FuelGauge

LED Worklight

Page 16

BITS (Fig. 8)

1.

Lock the trigger switch by placing the direction-of
OFF (center) position.

2.

Pull the sleeve towards

3.

Remove the bit from the hexagonal

4.

Release the sleeve.

17562

ManuaLRevised_lO

0607

rotation

selector

in the

the front of the tool, and hold it in place.
hole in the bit retainer.

Page 17

TIGHTENING SCREWS
NUTS (Fig. 9)
1.

Install the correct

AND

Fig. 9

\

I_ f-'l I11i 11 I-'I1[*']=1
A
All WARNING: To avoid serious personal injury, always remove the battery
pack from the tool when cleaning or performing any maintenance.

bit.

2. Apply just enough pressure
to keep the bit engaged on
the screw or nut.

WARNING: When servicing, use only identical Craftsman
Use of any other parts may create a hazard or cause product

replacement
damage.

parts.

&

3.

Position the direction-ofrotation selector to the left of
the tool for forward rotation.

4.

Apply minimal pressure to
the trigger switch initially.
Increase the speed only
when full control can be
maintained.

_i

WARNING:

_. WARNING:
It is not recommended
to use compressed
dry air as a cleaning
method for the Right-Angle Impact Driver. If cleaning with compressed air is the
only method available, always wear safety goggles or safety glasses with side
shields when using compressed air to clean the tool. If the operation is dusty,
also wear a dust mask.

GENERAL MAINTENANCE

Do not over-tighten,

as the force of the 12V Right-Angle

Driver can break the fastener. Keep the 12V Right-Angle Impact Driver
angle to the fastener to avoid damaging the fastener head.
LOOSENING

SCREWS

at a right

Install the correct

bit.

2.

Apply just enough pressure
to keep the bit engaged on
the screw or nut.

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible
to damage from various types of commercial solvents and may be damaged by
their use. Use clean cloths to remove dirt, dust, oil, grease, etc.
_,

WARNING:

Do not at any time let brake fluids,

gasoline,

petroleum-

based products,
penetrating
oils, etc. to come in contact with plastic parts.
Chemicals
can damage, weaken or destroy plastic which may result in
serious personal injury.

AND NUTS (Fig. 10)

1.

3.

Impact

[ Fig. 10
/

WARNING:

When servicing,

use only identical

Craftsman

replacement

parts.

Use of any other parts may create a hazard or cause product damage. To ensure
safety and reliability, all repairs should be performed by a qualified service
technician at a Sears Service Center.

Position the direction-ofrotation selector to the
right of the tool for forward
rotation.

4.

17562

Apply minimal pressure to
the trigger switch initially.
Increase the speed only
when full control can be
maintained.

ManuaLRevised_$0

0607

Page 18

17562

ManuaLRevised_10

0607

Page 19

BATTERIES:
The battery pack is equipped with Lithium-Ion
duration of use from each charge will depend

rechargeable batteries. The
on the type of work performed.

The batteries in this tool have been designed to provide maximum troublefree life. Like all batteries, they will eventually wear out. Do not disassemble
the battery pack or attempt to replace the batteries. Handling of the batteries,
especially when wearing rings and jewelry, could result in a serious burn.
To obtain the longest possible
operator's manual.
•

battery

CAUSE

The tool does not work

Battery

pack storage

SOLUTION
is depleted

Charge the battery

Sleeve is not released

Release the sleeve

Bit does not fit the sleeve

Use a 1/4" shank bit

Make sure that the cooling
vents are free from dust
and obstacles

Clean clear vents.
Do not cover vents

Bit cannot be installed

and follow this
Motor overheating

It is good practice to unplug the Charger/Adapter
Ion battery pack when not in use.

For Lithium-Ion
•

battery life, read, understand

PROBLEM

and remove the Lithium-

during operation

longer than 30 days:

Store the Lithium-Ion battery pack where the
temperature is below 80°F (26°C) and free of
moisture.
Store Lithium-Ion battery
charged condition.

packs in a 30%-50%

After every six months of storage,
the Lithium-Ion battery pack.

fully charge

Exterior may be cleaned with a cloth or soft
non-metallic brush.
BATTERY

PACK REMOVAL

AND PREPARATION

FOR RECYCLING

To preserve natural resources, please recycle or dispose of batteries properly.
This product contains lithium-ion batteries. Local, state, or federal laws may
prohibit disposal of lithium-ion batteries in ordinary trash. Consult your local
waste authority for information regarding available recycling and/or disposal
options.
WARNING:

Upon removal

of the battery pack for disposal

or recycling,

cover the battery pack's terminals with heavy-duty adhesive tape. Do not
attempt to destroy or disassemble the battery pack or remove any of its
components.
Lithium-Ion batteries must be recycled or disposed of properly.
Also, never touch both terminals with metal objects and/or body parts, as
short circuit may result. Keep away from children. Failure to comply with these
warnings could result in fire and/or serious injury.

17562

ManuaLRevised_$0

0607

Page 20

17562

ManuaLRevised_i0

0607

Page 2i

12.0-VOLT LITHIUM-ION
MODEL NO. 320. 17562

CORDLESS

RIGHT-ANGLE

IMPACT

DRIVER

The Model Number will be found on the Nameplate attached to the handle of the
Right-Angle Impact Driver. Always mention the Model Number when ordering
parts for this tool.

1

2730137000

DC Motor

1

2

3123113000

LED Cover

1

3

3123120000

Light Guide Pole

1

Exloded

4

3125334000

F/R Button

1

5

3125534000

Switch Trigger

1

6

3321025000

Left Housing

7

3321026000

Right Housing Assy

8

3402298000

Contact

9

3421092000

Left Gear Case

1

10

3421093000

Right Gear Case

1

11

3421145000

Bottom Support

1

12

3520410000

Gear

1

13

3520555000

Pinion

1

14

3550606000

Bush

1

15

3551501000

Impact Block

1

16

3551502000

Spindle

1

17

3551503000

Spindle

1

18

3551511000

Bevel Gear

1

19

3551528000

Bevel Gear

1

20

3551582000

Bush

1

21

3660177000

Spring

1

22

3660403000

Spring

1

23

3660437000

Spring

1

24

4890699000

PCB Assembly

1

25

5610012000

Tapping

Screw

2

26

5610013000

Tapping

Screw

7

27

5620006000

Hexagon Socket Screw

9

28

5620033000

Screw

2

29

5650003000

Spring Washer

7

17562

View

ManuaLRevised_lO

0607

Page 22

17562

ManuaLRevised_lO

0607

Assy

Receptacle

1
1
ASSY

1

Page 23

_o_nul

17562

30

5650192000

Washer

1

31

5650254000

Washer

2

32

5650349000

Washer

1

33

5650366000

Washer

2

34

5660035000

Circlips For Shaft

1

35

5690207000

Washer

1

36

5690222000

Washer

1

37

5700003000

Ball Bearing

2

38

5700044000

Steel Ball

23

39

5700053000

Needle Bearing

1

40

5700176000

Ball Bearing

1

41

5700178000

Steel Ball

2

42

5700226000

Steel Ball

2

ManuaLRevised_lO

0607

Page 24

17562

ManuaLRevised_lO

0607

Page 25

_o_nul

17562

ManuaLRevised_lO

0607

_o_nul

Page 26

17562

ManuaLRevised_lO

0607

Page 27

Your Home
For troubleshooting, product manuals and expert advice:

managemylife
www.managemylife.com

For repair- in your home - of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME

®

(1-800-469-4663)

Ca, anytime,dayor night
(U.S.A. and Canada)

www.sears.com

www.sears.ca

Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call anytime for the location of the nearest
Sears Parts & Repair Service Center
1-800-488-1222 (U.S.A.)
www.sears,com

1-800-469-4663 (Canada)
www.sears,ca

To purchase a protection agreement on a product serviced by Sears:
1-800-827-6655 (U.S.A.)
Para pedir servicio de reparaci6n
a domicilio, y para ordenar piezas:
1-888-SU-HOGAR®
(1-888-784-6427)
www.sears.com

1-800-361-6665 (Canada)
Au Canada pour service en franc_ais:
1-800-LE-FOYERMc
(1-800-533-6937)
www.sears.ca

Se llrS
TM
Trademark
/
Trademark
of KCD IP, LLC in the United States, or Sears Brands, LLC in other countries
® Marca Registrada
/ TM Marca de Ffibrica de KCD IP, LLC en Estados
Unidos, o Sears
Brands,
LLC in otros paises
_4CMarque de commerce
/ _4DMarque d6pos6e de Sears Brands, LLC
® Registered



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 15
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 4, 0, 0, 13
Create Date                     : Wed Jan 12 09:30:53 2011
Author                          : 
Title                           : 
Subject                         : 
EXIF Metadata provided by EXIF.tools

Navigation menu